







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Fence Installation: The Sunrise Manor Owner’s Guide
Fence installation using Schluter edge-protection and trim profiles in Sunrise Manor typically runs $3,500 – $9,000 installed, depending on fence length, material, and how much trim detailing you want. We match the correct Schluter profile to your fence system, give you a written price before any work starts, and schedule most projects within one to two weeks of approval. Schluter trim on a fence usually shows its first failure signs slowly: a white chalky film on the metal edge, a hairline gap where the profile meets the panel, or screws that back out after a windy spring.
Most Sunrise Manor owners notice the problem when they’re doing yard work and see the trim lifting away from the fence line, or when a gate starts dragging because the bottom profile has shifted. By then the edge has often been soaking up monsoon rain for a season or two.
Which Schluter Models This Applies To

Schluter trim profiles are sized by the thickness of the material they’re designed to cap. On fence work, the profiles you’ll see most are metal edge trims in the 3/8-inch to 1/2-inch range, plus the wider 5/8-inch and 3/4-inch versions for thicker composite panels. The number on the strip’s packaging corresponds to that leg dimension, not to the total width, and that’s the single biggest compatibility gotcha we run into. A homeowner buys a “1/2-inch” strip expecting it to cover a 1/2-inch panel and finds the legs too short to grip properly.
To identify the right part, measure the actual panel thickness with a caliper or a tape at three points along the edge. Look for a printed part code on the original packaging if you still have it, or the faint stamping on the back face of the profile. If your fence is composite or capped wood, check whether the profile you’re replacing was a standard edge trim or a transition piece between two different panel heights.
On the OEM question: Schluter-brand profile stock is consistent, so replacing with the same line is straightforward when you can find it locally. A quality aftermarket extrusion with the same leg depth and alloy will do the job, but the finish coat and screw-hole placement differ. We compare both before recommending anything.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Fence Installation Is Failing
Trim profiles don’t fail all at once. Here’s what we see, and why:
- White chalky residue on the metal face. That’s the anodized or powder-coated finish breaking down from UV. Sunrise Manor gets around 290 sunny days a year, and fence trim faces south or west all day.
- Gaps between the profile leg and the panel. Usually thermal expansion. Composite panels expand more than the metal profile, and over a few summers the joint opens and lets water in.
- Screws backing out or rusting at the head. Monsoon moisture wicks into the screw hole and corrodes the fastener. Once the head is compromised, wind lift takes the profile with it.
- The profile lifting at corners or gate jambs. Gate posts move more than line posts, and the trim at a jamb takes the stress. This is where we see it fail first on almost every Sunrise Manor repair.
- Panel edges swelling or delaminating under the trim. This means water got behind the profile and stayed. The metal is fine; the panel underneath is the casualty.
Replacement Cost & What’s Included

Fence installation with Schluter-compatible trim in Sunrise Manor runs $3,500 – $9,000 installed. What drives the number:
| Line Item | Typical Range |
|---|---|
| Schluter profile material (per linear foot) | $4 – $11 |
| Labor to remove old trim and install new | $12 – $22 per linear foot |
| Panel edge repair where water damage is found | $150 – $600 per affected section |
| Gate jamb re-trim and re-hang | $200 – $550 |
You get a written, line-item price before we touch the fence, and the work is covered by our 365-Day Done Right Promise. If a profile we installed lifts or fails within a year of completion, we come back and fix it at no cost to you. Mason Remodeling Sunrise Manor is an independent service provider and is not affiliated with Schluter.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check panel thickness, photograph the failing profile, and note the part code if it’s legible. You can also confirm whether the panel under the trim is swelling. That’s diagnostic work, and it helps us quote accurately.
Where homeowners get into trouble is re-fastening a profile without addressing the water path behind it, or forcing a strip onto a panel that’s outside the profile’s leg tolerance. That’s how the same corner fails twice within a season. There’s also a moderate risk of cuts and eye injury working with metal trim overhead, so eye protection is non-negotiable if you attempt any of it.
Call (855) 606-6122 and we’ll get a written price to you.
FAQs

Seven to twelve years is realistic here, less on south-facing runs with full sun. The UV load in Sunrise Manor is harder on the finish than on inland profiles, and monsoon-driven moisture at the fasteners is what shortens the back side of that range.
Sometimes, yes. If the finish is intact and only the fasteners failed, we can re-secure it and seal the joint. Call (855) 606-6122 for an assessment, and we’ll tell you honestly which way it should go.
A typical Sunrise Manor fence trim job runs one to two days, depending on length and whether gate jambs are involved. We give you the timeline with the written price.
We match to the profile’s leg depth and alloy from verified suppliers, and compare OEM against quality aftermarket options before recommending one. Call (855) 606-6122 for a free estimate.
Contact Us
Call Mason Remodeling Sunrise Manor at (855) 606-6122 for a free estimate on Schluter fence trim in Sunrise Manor. You’ll get a written, line-item price before any work starts, and a live person answers the phone. We also work with KraftMaid, Cambria, and Silestone products.
Written by the team at Mason Remodeling Sunrise Manor, serving Sunrise Manor and nearby areas.












