







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Driveway & Pavers: The Sunrise Manor Owner’s Guide
We install CGI-compatible driveway and paver systems for Sunrise Manor homeowners, and the honest answer on price is this: a full paver driveway runs $7,000 – $18,000 installed, while a concrete driveway replacement lands between $4,500 – $12,000. Cosmetic fixes like re-sanding and sealing sit far lower, at $250 – $700. Because pavers are a surface good rather than a motorized part, there is no same-day “swap” – most driveways take several days once materials are on site. We schedule those days on a written timeline you approve before we start.
Owners usually realize something has gone wrong the same way. A paver lifts slightly under a tire in July, or the sand between units washes out after a monsoon afternoon and a joint opens up. Sometimes it’s a hairline crack spreading across a concrete slab poured a decade ago. Sunrise Manor sits on expansive desert soils and takes brutal summer heat, and that combination finds weak points in any hardscape faster than most people expect.
Key Takeaways
- CGI-compatible pavers must match base depth and joint spec, not just color and shape.
- Sunrise Manor soil movement causes most paver settling; base prep matters more than the paver itself.
- Installed paver driveways in Sunrise Manor run $7,000 – $18,000; concrete runs $4,500 – $12,000.
- We are an independent service provider, not affiliated with CGI.
- Every job gets a written price before work starts and a 365-Day Done Right Promise.
Which CGI Models This Applies To

CGI paver systems follow the manufacturer’s unit dimensions and edge-restraint profiles rather than a model number stamped on a plate, so matching the right product means reading the actual spec. The most common failure in matching is assuming a “6×9” paver is 6×9 inches – many CGI series measure the face differently once the joint gap is included, which throws off coverage area by 5 to 8 percent and leaves a project short of material. We measure the existing units, check the color family against the batch code on the original pallet if you still have it, and confirm base depth requirements before quoting.
On the OEM-versus-aftermarket question: CGI’s own series pavers are the clean match if you’re replicating a small repair. For a full driveway, a professional-grade equivalent from Belgard, Unilock, or Techo-Bloc will often outperform on frost resistance and color fastness at similar cost. We spec both – CGI when the repair demands an exact visual match, and the strong domestic equivalents when you’re replacing the whole surface. If you’re unsure which path fits, we’ll tell you straight in the estimate.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Driveway & Pavers Is Failing
- Individual pavers tilting or rocking underfoot. This almost always means the base layer beneath has compacted unevenly, not that the paver itself is defective. Desert soil expands and contracts with moisture, and a base that wasn’t compacted in lifts will shift within a season or two.
- Sand washing out of the joints. Polymer or joint sand lost after rain exposes the paver edges to chipping and lets weeds take hold. Sunrise Manor’s sudden downpours push sand out fast if joints weren’t sealed properly at install.
- Hairline cracks spreading on a concrete slab. Shrinkage cracks are normal in concrete, but cracks wider than a credit card or cracks that crisscross indicate a structural slab problem that likely needs full replacement, not patching.
- Sunken or heaved sections along the driveway edge. Edge restraint failure lets pavers creep outward until a section drops. This is the single most common paver repair we see in Sunrise Manor, and it’s fixable without replacing the whole drive.
- Faded or chalky surface color. UV exposure in Las Vegas Valley sun degrades low-grade pavers faster than quality ones. If the color is washing out within five to eight years, the paver likely wasn’t the right grade for this climate.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Pricing in Sunrise Manor breaks down by surface type and scope. A full paver driveway install runs $7,000 – $18,000; concrete comes in at $4,500 – $12,000; asphalt paving sits at $3,500 – $9,000; a straight driveway replacement (any surface) lands at $5,000 – $14,000. Re-sanding and sealing alone is $250 – $700. A paver patio install, if you’re extending the hardscape, runs $3,500 – $11,000.
What drives the range: square footage, base depth, edge restraint type, drainage corrections, and whether old material needs haul-off. Every quote is written line by line – material, labor, base prep, disposal – so you can see where the money goes. No verbal estimates that grow on the final bill. The workmanship itself is covered by our 365-Day Done Right Promise: if something we installed fails within a year of completion, we make it right at no cost.
DIY or Call Us?
You can safely inspect your own driveway. Run a level across a section to spot heaving, press a joint to check sand firmness, and count the paver courses if you’re planning a repair. Those checks are harmless and useful.
What you shouldn’t do yourself: excavate and re-set base material for a sunken section, or attempt a full paver install without proper plate compaction in lifts. Getting the base wrong looks fine for a season and then fails – which costs more to fix than doing it right the first time. There is no dangerous tension or live wire here, but the labor is real and the base is what holds everything. We’ve had homeowners come to us after a DIY weekend that lasted one winter. If you’re at that point, call (855) 606-6122 and we’ll walk you through what a proper fix looks like, free.
Also worth noting: we handle all types of hardscape work, and if your project includes cabinet or countertop updates in the same season, we can coordinate with our KraftMaid, Cambria, and Silestone partners on those too.
FAQs

A properly installed paver driveway typically lasts 20 to 30 years in this climate if base prep was done right and joints are maintained. UV exposure and soil movement are the two biggest threats – sealing every two to three years adds years to the life. Call (855) 606-6122 for an exact quote on sealing or repair.
Yes, in most cases. A single sunken section, edge failure, or damaged paver is fixable without replacing the full drive. We pull the affected units, re-compact the base, and relay them – typically a half-day job. We’ll confirm during the estimate whether a section repair is the right call.
Most full driveway installs take three to five days on site, depending on square footage and whether old material needs removal. We schedule the days in writing before we start, so you know the timeline. Call (855) 606-6122 to get a timeline estimate for your project.
We source through professional material partners including CGI series distributors, Belgard, Unilock, and Techo-Bloc, depending on what the repair or install calls for. We specify the grade, color family, and joint spec in the written quote. We are an independent provider and not affiliated with CGI. Call (855) 606-6122 to discuss which product fits your project.
Call (855) 606-6122 for a free estimate. We’ll send a written price before any work starts, and every crew member is background-checked, arrives in a clean uniform, and shows a photo ID badge at your door under The Threshold Standard.
Written by the team at Mason Remodeling Sunrise Manor.












