







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Home Additions & ADU: The Sunrise Manor Owner’s Guide
Home additions and ADU work in Sunrise Manor typically runs $45,000 – $130,000 for an addition and $90,000 – $220,000 for a detached or attached accessory dwelling unit, with Barrette-specified framing, glazing, and trim lines installed by our crews. Mason Remodeling Sunrise Manor is an independent service provider and is not affiliated with Barrette. We work with Barrette-compatible systems but source and install as a general contractor, not as a Barrette dealer.
Homeowners in Sunrise Manor usually discover a Barrette product failure the same way: a hairline crack spreading along a glazed panel, a door or window slab that no longer seats, or a header trim piece that has started pulling away from the wall plate. That’s the third or fourth season of thermal cycling catching up. Sunrise Manor sits in one of the harshest swing zones in the valley – 40-degree days in January and 110-degree afternoons in July – and Barrette units installed without proper drainage detailing at the sill tend to telegraph the problem within the first two summers. When the fascia starts waving, the glazing starts fogging, or a sliding panel drags on its track, the part is usually at the end of its service life, not mid-failure.
Which Barrette Models This Applies To

Barrette’s residential line covers a wide range of door, window, and glazing assemblies, and the part that fits a 2018 build in Sunrise Manor will not necessarily fit a 2014 model with a shallower frame depth. The model and series code is stamped on the frame plate, usually inside the jamb reveal or just above the sill on a sliding unit. If the label is gone, measure the rough opening and the frame face width – Barrette’s standard rough-opening callouts are published in their installation guides, and a 1/2-inch difference in the frame face is enough to send the wrong extrusion home.
For Sunrise Manor, the compatibility gotcha is the stucco flange configuration: Barrette’s western line commonly ships with a nail-fin flange sized for stucco or hard-coat assemblies, and the flange depth must match the substrate thickness at the header. Mismatch here is the number one cause of the water intrusion we see on additions in the eastern valley. OEM Barrette replacement parts carry the exact correct flange and sill pan geometry; quality aftermarket equivalents exist for glazing and hardware, but the structural frame members should stay OEM whenever the original rough opening is being reused.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Home Additions & ADU Is Failing
- Fogging or condensation between glazing panes. The seal has failed and moisture is inside the unit. Barrette’s dual-pane assemblies should stay clear for 15 to 20 years in Vegas; fogging before year 10 usually means a defective seal at the spacer.
- Sliding panel drags or jumps the track. Rollers or the track itself have worn, and the alignment has shifted. In Sunrise Manor, dust and fine desert grit accelerate roller wear by roughly 30% compared to cooler, cleaner climates.
- Fascia or header trim pulling away. Fasteners have backed out of the substrate, which almost always traces to thermal expansion stress. If the gap is more than 1/8 inch, the trim is compromised.
- Water stains inside the frame at the sill. The sill pan or flange detail has failed and water is entering. This is the failure that causes the most damage to an addition or ADU wall assembly if it goes unaddressed.
- Door or window no longer seats in the frame. Either the frame has racked (a structural problem) or the slab has warped (a part problem). The distinction matters before you order anything.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a Sunrise Manor Barrette unit replacement within a home addition or ADU, plan on the following installed ranges:
- Full addition (Barrette glazing specified): $45,000 – $130,000
- ADU construction (Barrette-specified units): $90,000 – $220,000
- Garage conversion with new Barrette glazing: $30,000 – $80,000
- Individual Barrette unit replacement (framed opening): typically $800 – $3,500 per unit, varies by size and glazing package
The range is driven by opening size, glazing package (dual vs triple pane, low-E coating), whether the rough opening can be reused, and whether stucco or hard-coat repair is needed after removal. Every Mason Remodeling Sunrise Manor project comes with a written price before work begins, and every installation is covered by our 365-Day Done Right Promise. If a repair or installation fails within a year of completion, we come back at no charge.
DIY or Call Us?
You can safely check a few things yourself. Inspect the frame label for the model code. Measure the rough opening. Test whether a door or window seats in the frame by watching for daylight at the corners. Those checks give us the information to quote the right part before we arrive.
What you shouldn’t attempt on your own is removing or reinstalling a Barrette unit in a load-bearing addition wall. This work involves header support, flashing integration, and stucco tie-in – a mistake there lets water into the wall cavity and can compromise the structural opening. The failure doesn’t show up for a season, and by then the repair is in the thousands. Call Mason Remodeling Sunrise Manor at (855) 606-6122 with your model code and opening measurements and we’ll price the replacement honestly before anyone touches the wall.
FAQs

Plan on 15 to 25 years for the frame and 15 to 20 years for sealed glazing in the Sunrise Manor climate, with proper flashing and drainage detailing at installation. Units installed with a mismatched flange or missing sill pan often fail in 8 to 12 years. Call (855) 606-6122 for an inspection if you’re past year 10 and seeing fogging.
Sometimes yes. Hardware, rollers, weatherstripping, and individual glazing units can be replaced in many Barrette models without touching the frame. Racked frames and failed sill pans usually require full replacement. Our technicians will tell you which case you’re in before quoting anything.
A single Barrette unit replacement in a Sunrise Manor addition or ADU takes most of one day once the correct part is on site, including stucco patching where needed. Multi-unit replacements or work that requires header modification can run two to three days. We schedule around weather and give you the timeline in writing before we start.
We order directly from Barrette’s replacement parts channel using your model code and rough-opening measurements. That avoids the wrong-flange problem that aftermarket catalogs often miss. Lead time is typically 2 to 4 weeks for custom sizes and 3 to 7 days for stock configurations. Our teams also work alongside KraftMaid, Cambria, and Silestone on the finishes side of the same project if you’re remodeling the space behind the Barrette unit at the same time.
If your Barrette addition or ADU unit is failing, the fastest path to a written price is a call. Reach Mason Remodeling Sunrise Manor at (855) 606-6122 for a free estimate. Every project gets a background-checked, uniformed technician introduced by name and photo before the visit, a written price before work starts, and our 365-Day Done Right Promise on the finished install.
Written by the team at Mason Remodeling Sunrise Manor, serving Sunrise Manor and nearby areas.












