







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Sunrise Manor Owner’s Guide
We build and finish home additions and ADUs in Sunrise Manor using Schluter systems where tile meets floor, wall, and shower, and a typical addition runs $45,000 – $130,000 installed, with detached ADUs from $90,000 – $220,000. If you’re here because a Schluter profile, membrane, or trim piece has failed, you’re probably seeing a loose edge, a cracked grout line, or a hollow-sounding tile at the transition between your addition and the original house. That’s how most Sunrise Manor owners find us – the part didn’t announce itself, the floor did.
An addition makes every one of those transitions harder. New slab meets old slab. New tile meets a 1950s porch. A Schluter profile is what bridges that gap cleanly, and when it’s the wrong size or wrongly seated, Sunrise Manor’s summer heat and monsoon moisture find it fast.
Key Takeaways
- Schluter profiles and membranes fail at transitions first – that’s where you’ll see it.
- We’re an independent contractor, not affiliated with Schluter. We install Schluter-compatible systems only.
- Sunrise Manor’s 100°F-plus summers and hard water put real stress on any tile edge that isn’t seated correctly.
- Your written price comes before any work starts, on every project – that’s standard, not an upgrade.
- Call us at (855) 606-6122 – a live person answers, any hour.
Which Schluter Models This Applies To

Schluter makes dozens of profiles, and the naming trips people up. The profile you’re pulling off your addition’s edge is almost certainly one of these: SCHIENE (the sloped metal edge for tile-to-floor), RENO-U or RENO-TK (the ramp and T-shaped profiles that cover the step down to a lower floor – common where an addition sits a few inches above the original slab), DILEX (movement joints), TREP (stair nosings), and JOLLY (wall-corner trim). If the failure is under the tile rather than at the edge, you’re dealing with KERDI membrane or DITRA uncoupling mat.
Find the model on the flange or the plastic wrap before it’s gone; Schluter prints the profile name and dimensions right on it. The number that matters most is the inside height – the profile has to match the tile thickness plus the thinset layer. A SCHIENE at 3/8 inch won’t sit flush over a 1/2-inch porcelain, and that mismatch is exactly why so many Sunrise Manor additions show a lifted lip at the door threshold two summers in.
On new vs. the original: Schluter controls its own spec, so there’s no true aftermarket clone of a Schluter profile. There are quality equivalents from other manufacturers (Genesis, Blanke, Prova), and for a straightforward rectilinear edge they perform fine. For a complex shape, an anodized or brushed-finish profile, or anything under a wet-area membrane, we spec the Schluter part. Call (855) 606-6122 and we’ll match your profile to the right part size before we order.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
Most Sunrise Manor failures show up as five specific things. Here’s what each one is telling you.
- A lifted or loose edge profile. Thinset that was mixed too dry, or a profile set before the mortar skimmed over, never bonds fully. Heat cycling opens the gap.
- Hairline cracks along the profile’s line. Usually a movement joint was skipped where the addition meets the original structure. The two slabs move, and the tile takes the stress.
- Hollow-sounding tile at the transition. Water got under the KERDI or DITRA at an unsealed edge. Common after monsoon season, when the ground swells and the edge flexes.
- Discoloring or efflorescence at the seam. Hard water from the tap plus salt from the slab is wicking up. Tells you the bond is compromised, not just a cosmetic stain.
- A rocking or sharp step-down at the doorway. A RENO profile was set to the wrong height, or it was replaced once already and never sat flush.
If you’re seeing more than one, the profile isn’t the whole story – the substrate under it likely needs checking. That’s the point where a free second look saves a much bigger repair. Call (855) 606-6122 to set it up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For a profile swap or a re-set at a doorway transition, most Sunrise Manor jobs run $450 – $1,200 in labor, depending on how much tile has to come up around the edge. Where the membrane under the tile has failed, the scope moves into a partial re-tile of the transition, and that’s where the numbers climb.
| Scope | Typical Installed Range |
|---|---|
| Profile / trim swap at one transition | $450 – $1,200 |
| Partial re-tile with new membrane at transition | $2,000 – $6,500 |
| Kitchen remodel (tile, trim, Schluter edge) | $14,000 – $45,000 |
| Bathroom remodel (full watertight system) | $9,000 – $28,000 |
| Home addition, finished | $45,000 – $130,000 |
| ADU construction | $90,000 – $220,000 |
| Garage conversion | $30,000 – $80,000 |
What drives the range: how much tile has to come up, whether the substrate under it is sound, and whether we’re matching discontinued tile. On any addition, our written price lands before a tool comes out – parts, labor, and the finish line itemized. The work is backed by the 365-Day Done Right Promise: if it isn’t right within a year of completion, we come back and make it right at no cost to you.
DIY or Call Us?
Owners can safely do two things on their own: look for the profile name and size on the piece (or the original packaging), and press on the tile around the edge to hear that hollow sound. Both tell you what you’re dealing with. Neither involves a saw.
Where it goes wrong: pulling up a seated profile almost always cracks the tile behind it, and re-setting one requires the right thinset over the right height, cured properly. Set a Schluter profile with the wrong mortar or before the bed has skimmed and it fails again in a year – often worse, because now there’s tile missing. We don’t recommend it. Especially on a door threshold, that edge takes every footstep in the house.
Call (855) 606-6122 for a free estimate. Before we arrive, you’ll get the name and photo of the technician coming, and they’ll show an ID badge at the door. A live person answers any time – request a callback and we’ll confirm your window.
FAQs

Set correctly over a sound substrate, a Schluter metal profile should last 20 to 30 years or more. In Sunrise Manor, the limiting factor is the wear on the finish – the anodized layer on an edge profile in a busy doorway scuffs in 8 to 12 years, and the profile is still sound while the finish is worn. Replacement at that point is cosmetic.
Sometimes. If the profile is intact and only loosened at one spot, we can re-bond it without removing tile. If the profile is cracked, bent, or the tile behind it is hollow, it has to be replaced, and the surrounding tile comes up with it. Call (855) 606-6122 for a free look – we’ll tell you honestly which situation you’re in.
A simple re-set runs 2 to 3 hours on site. A partial re-tile with a new membrane at the transition typically takes 1 to 2 days, mostly curing time – the thinset and grout have to set before foot traffic. We’ll give you the exact window in your written estimate.
We order from Schluter’s distribution channel, matching your profile by name and inside height before the order goes out. Because Schluter controls its own spec, there’s no true aftermarket clone; when we do spec an equivalent from another maker, we tell you which and why. We don’t stock parts on a truck – the part is ordered to your job.
No. The written price you receive before work begins is what you pay for the scope listed. If we open the transition and find something not visible in the original estimate – soft subfloor, missing membrane – we stop, show you, and price the addition before anyone continues. No surprise invoices.
We also handle cabinetry and surfaces on additions and ADUs – KraftMaid and Wellborn cabinets, Cambria and Silestone tops – as part of the same written scope.
Mason Remodeling Sunrise Manor is an independent remodeling contractor and is not affiliated with Schluter Systems. We install Schluter-compatible systems and quality equivalents.
For a free estimate on your Sunrise Manor addition, ADU, or transition repair, call (855) 606-6122. Live person, every hour, every day.
Written by the team at Mason Remodeling Sunrise Manor, serving Sunrise Manor and nearby areas.












